3545 cadillac avenue ? costa mesa, ca 92626-1401 ? (714) 433-1200 ? fax (714) 433-1234 marketing bulletin date: march 24 th , 2006 to: all sales personnel from: mark stoner re: product termination to all concerned parties, this bulletin is to notify all customers of the discontinuation of the following ecliptek series effective march 24 th , 2006: series description recommended replacement E13C9 3.3v 5 x 7mm smd lvpecl oscillator e13c7 or e13d8 in compliance with our end of life (eol) policy, this will serve as advanced notice of product termination. new orders wil l not be accepted after july 1 st , 2006, with delivery to conclude by october 1 st 2006. if there are any questions pertaining to this bulletin, please fell free to contact me. thank you again for your cooperation. best regards, mark w. stoner director of marketing ecliptek corporation
manufacturer category series package voltage class rev . date ecliptek corp. oscillator E13C9 ceramic 3.3v os1t 06/04 E13C9 series oscillator E13C9 electrical specifications 800-ecliptek www.ecliptek.com for latest revision specifications subject to change without notice. ? rohs compliant (pb-free) lvpecl output oscillators 3.3v supply voltage at-cut fundamental mode inverted mesa crystal ceramic 6-pad smd package stability to 25ppm tri-state enable high and enable low options available on pad 1 or pad 2 complementary output wide range of available frequencies 19.440mhz to 200.000mhz 0c to 70c, or -40c to +85c -55c to 125c 3.3v dc 5% 75ma maximum 100ppm, 50ppm, or 25ppm maximum v cc -1.025v dc minimum v cc -1.620v dc maximum 1.5 nseconds maximum, 600 psec typical 50 10(%) 50 5(%) 50 ohms into v cc -2.0v dc no connect and complementary output or tri-state and complementary output enables output enables output disables output: high impedance disables output: high impedance enables output enables output 25ma maximum 10 mseconds maximum 5 psec maximum 2 psec maximum 1 psec maximum -75dbc/hz typical -95dbc/hz typical -125dbc/hz typical -140dbc/hz typical -145dbc/hz typical nominal frequency operating temperature range storage temperature range supply voltage (v cc ) input current frequency tolerance / stability output voltage logic high (v oh ) output voltage logic low (v ol ) rise time / fall time duty cycle load drive capability logic control / additional output enable high tri-state input voltage enable low tri-state input voltage output disable current start up time rms phase jitter phase noise (at 155.520mhz) inclusive of all conditions: calibration tolerance at 25c, frequency stability over the operating temperature range, supply voltage change, output load change, 1st year aging at 25c, shock, and vibration 20% to 80% of waveform at 50% of waveform enable high or enable low v ih of 70% of v cc minimum no connection v il of 30% of v cc maximum v ih of 70% of v cc minimum no connection v il of 30% of v cc maximum < 44.736mhz; f j = 12khz to 20mhz > 44.736mhz, < 77.760mhz; f j = 12khz to 20mhz > 77.760mhz; f j = 12khz to 20mhz at 10hz offset at 100hz offset at 1khz offset at 10khz offset at 100khz offset h 2.0 l 7.0 w 5.0
line 1: ecliptek line 2: xx.xxx m frequency in mhz (5 digits maximum + decimal) line 3: xx y zz week of year last digit of year ecliptek manufacturing identifier manufacturer category series package voltage class rev . date ecliptek corp. oscillator E13C9 ceramic 3.3v os1t 06/04 mechanical dimensions all dimensions in millimeters environmental/mechanical specifications marking specifications tape and reel dimensions all dimensions in millimeters suggested solder pad layout all dimensions in millimeters 800-ecliptek www.ecliptek.com for latest revision specifications subject to change without notice. E13C9 e 2 f - 155.520m tr part numbering guide available options blank=tubes tr=tape and reel (standard) frequency logic control/additional output c=no connect and complementary output f=tri-state (enable high) on pad 1 and complementary output h=tri-state (enable high) on pad 2 and complementary output j=tri-state (enable low) on pad 1 and complementary output k=tri-state (enable low) on pad 2 and complementary output frequency tolerance & stability/ operating temperature range c=100ppm maximum over 0c to +70c d=50ppm maximum over 0c to +70c e=25ppm maximum over 0c to +70c g=100ppm maximum over -40c to +85c h=50ppm maximum over -40c to +85c j=25ppm maximum over -40c to +85c duty cycle 1=50% 10%, 2=50% 5% a b c d e f 16.3-.1 7.5.1 6.75.1 4 .1 2.1 f g h j k l 8.1 b0* 1.5 +.1-0 a0* .3 .05 k0* tape m n o p q 1.5 min 50 min 20.2 min 13.2 40 min r s t u v qty/reel 2.5 min 10 min 22.4 max 360 max 16.4+2-0 1,000 reel *compliant to eia 481a tolerances= +0.1 characteristic specification fine leak test mil-std-883, method 1014, condition a gross leak test mil-std-883, method 1014, condition c mechanical shock mil-std-202, method 213, condition c vibration mil-std-883, method 2007, condition a solderability mil-std-883, method 2002 temperature cycling mil-std-883, method 1010 resistance to soldering heat mil-std-202, method 210 resistance to solvents mil-std-202, method 215 pin 1: tri-state or no connect pin 2: tri-state or no connect pin 3: case ground pin 4: output pin 5: complementary output pin 6: supply voltage
|
